【資料名稱】：RRU升級打印消息解讀

【資料作者】：11

【資料日期】：11

【資料語言】：中文

【資料格式】：DOC

【資料目錄和簡介】：

.s8Buf[]={[dd_init_hook]: chkdsk succeed.//磁盤檢測
.s8Buf[]={STARTING RRS.................................//RRS啟動，初始化
.s8Buf[]={RRS INITIALIZING.................
.s8Buf[]={SFU:0x9050032, FILE:dd_ifp_ccm_util.c LINE:5858, AlarmNo:101, AlarmValue:0, AlarmClearFlag:1ErrMsg>RRS RESET,RESET REASON: 0x160,REG 0x0A: 0x20,REG 0x2F: 0xe,NOTEPAD REG: 0x0
.s8Buf[]={RRS START DOWNLOADING DFE0 FPGA........................
.s8Buf[]={RRS START DOWNLOADING DFE1 FPGA........................
.s8Buf[]={RRS START DOWNLOADING DFE2 FPGA........................
.s8Buf[]={DFE FPGA DOWNLOAD COMPLETE............................//中頻FPGA下載
.s8Buf[]={RRS SELF TEST...........//RRS自檢
.s8Buf[]={TRB_0 EEPROM CRC CHECK ERROR!
.s8Buf[]={TRB_1 EEPROM CRC CHECK ERROR!
.s8Buf[]={TRB_2 EEPROM CRC CHECK ERROR!
.s8Buf[]={TRB_6 EEPROM CRC CHECK ERROR!
.s8Buf[]={TRB_7 EEPROM CRC CHECK ERROR!
.s8Buf[]={aCDB CAL EEPROM CRC CHECK ERROR!//由于EEPROM中CRC值沒有填寫導致CRC錯誤，實際上是可以通過，不告警的，這個沒有關系，不需關注
.s8Buf[]={RRS START EQUIPMENT USABILITY CHECK.........................
.s8Buf[]={RRS START DOWNLOADING FPGA........................
.s8Buf[]={RRS DOWNLOAD FPGA COMPLETE............................//FPGA下載完成
.s8Buf[]={RRS OPEN FPGA INTERRUPT........................
.s8Buf[]={RRS EQUIPMENT USABILITY CHECK COMPLETE.........................//設備可用性檢測完成
.s8Buf[]={SFU:0x905003b, FILEsp_dd_ifu_int.c LINE:597, AlarmNo:21701, AlarmValue:1, AlarmClearFlag:0ErrMsg>HW EPLD EXCEPTION, ISRTIMES:1,TASKTIMES:1
.s8Buf[]={RRS START CHECK ERU...............
.s8Buf[]={RRS START TIME DELAY MEASURE......................... //開始時延測量
.s8Buf[]={RRS TDRI DELAY FROM E2PROM IS INVALID............
.s8Buf[]={CONFIG TDRI DELAY = 0x2E (5M) ...........
.s8Buf[]={WAITING FOR SLAVE TDRI DCM COMPLETED..........
.s8Buf[]={
.s8Buf[]={TRB Gain Calculation, Path_0//各通道增益依次校準，同一通道先做發(fā)方向，然后做收方向
.s8Buf[]={Get Parameters://獲取參數(shù)
.s8Buf[]={t0 = 6400; t = 8704; s16K2G = 190; s16K3G = 485;
.s8Buf[]={s16G0Fix[0] = 17401; s16G0Fix[1] = 17782; s16G0Fix[2]= 17707;
.s8Buf[]={s16K1G[0] = -3082; s16K1G[1] = -3082; s16K1G[2]= -3082;
.s8Buf[]={s16GfilFt[0] = -384; s16GfilFt[1] = -384; s16GfilFt[2]= -384;
.s8Buf[]={Fi[0] = 10062; Fi[1] = 10087; Fi[2]= 10112;
.s8Buf[]={Start Calculation://開始Tx方向校準
.s8Buf[]={s16GfixFt[0] = 17289; s16GfixFt[1] = 17670; s16GfixFt[2]= 17595;
.s8Buf[]={u16Freq[0] = 10087; Fh = 10112; Fl = 10087;
.s8Buf[]={s16GfilPath[0] = -384; s16GfixPath[0] = 17670;
.s8Buf[]={s16GpgcTx(F) = s16PnomTxOut - s16IfHasEruGainTx - Gfil(F) - Gfix(F) - s16PnomTxIn
.s8Buf[]={ s16PnomTxOut = 8960; s16PnomTxIn = -5120; s16IfHasEruGainTx = 0; GpgcTx[0] = -3206;
.s8Buf[]={s16Gmax = -3206; s16Gmin = -3206
.s8Buf[]={TRBGpgcTx[0] = -3072;
.s8Buf[]={s16Agc[0] = -134;
.s8Buf[]={
.s8Buf[]={TRB Gain Calculation, Path_0
.s8Buf[]={Get Parameters://獲取參數(shù)